State-of-the-art packed bed models supply continuous concentration profiles as boundary conditions for subsequent CFD simulations of gas phase, leading to pre-mixed combustion conditions. However, in reality the “porous” nature of the packed bed leads to streak formation influencing gas mixing and combustion. Therefore, in the present work, in order to account for the influence of the streaks on gas phase combustion, a gas streak model based on a correlation between the local gas residence time and a mixing time has been developed based on numerical simulations. Finally, the streak model was linked with an in-housed developed hybrid gas phase combustion model suitable for laminar to highly turbulent flow conditions and applied for an under-feed pellet stoker furnace (20 kW_th) concerning the simulation of gas phase combustion and NO_x formation. The results in comparison with a simulation without the streak formation model show that the flue gas species prediction can be improved with the proposed streak formation model. Especially, in the region above the fuel bed (in the primary combustion chamber), this is of special importance for NO_x reduction by primary measures.

Since batch-wise operated biomass roomheaters are claimed to cause high amounts of gaseous and particulate emissions effective measures for a reduction of these emissions especially in real life operation have to be implemented in the future. For a verification of the real life operation performance as well as for a better product differentiation of biomass room heating appliances on the market advanced testing methods will be necessary in the future. Therefore a new test method for roomheaters called “Stove Testing 2020” (ST2020) was developed. According to the new test method the emission and efficiency performance of roomheaters is determined under operating conditions that are closer to real life. Compared to the existing EN 13240 standard also transient combustion phases are included. For a final evaluation of the test method the reproducibility as well as the real life relevance was analysed by a Round-Robin-Test as well as by field tests. The results showed sufficient reproducibility as well as a high real life relevance of the ST2020 test method. However, due to the strong impact of user behavior on emission and efficiency performance in real life operation further technological improvements of biomass roomheaters have to be strongly supported by effective measures to guarantee a correct operation.

A novel hybrid gas phase combustion model suitable for low as well as high turbulent combustion conditions is proposed. In particular, in the region above the fuel bed of small-scale biomass combustion plants, gas phase mixing is highly influenced by laminar and low turbulence zones. Here, the eddy break-up combustion models are not valid because they were originally developed for highly turbulent flows. Therefore, a CFD gas phase reaction model applicable over the whole Reynolds range from laminar to turbulent flows is developed. It is a hybrid Eddy Dissipation Concept/finite rate kinetics model which calculates the effective reaction rate from laminar finite rate kinetics and the turbulent reaction rate and weights them depending on the local turbulent Reynolds number of the flow. To validate the proposed model, comparisons are made with experimental data for a series of jet flames covering laminar, transitional, and turbulent flow conditions. The simulation results show that the prediction of flame can be improved with the proposed hybrid combustion model. © 2014 Elsevier Ltd. All rights reserved.

urpose: Decreasing energy demand due to improved building standards requires the development of new biomass combustion technologies to be able to provide individual biomass heating solutions. The purpose of this paper is, therefore, the development of a pellet water heating stove with minimal emission at high thermal efficiency. Design/methodology/approach: The single components of a 10 kW water heating pellet stove are analysed and partly redesigned considering the latest scientific findings and experimental know-how in combustion engineering. The outcome of this development is a 12 kW prototype which is subsequently down-scaled to a 6 kW prototype. Finally, the results of the development are evaluated by testing of an accredited institute. Findings: Based on an existing pellet water heating stove, the total excess air ratio was reduced, a strict air staging was implemented and the fuel supply was homogenized. All three measures improved the operating performance regarding emissions and thermal efficiency. The evaluation of the development process showed that the CO emissions are reduced by over 90 per cent during full load and by 30-60 per cent during minimum load conditions. Emissions of particulate matter are reduced by 70 per cent and the thermal efficiency increased to 95 per cent. Originality/value: The result represents a new state of technology in this sector for minimal emissions and maximal thermal efficiency, which surpasses the directives of the Eco label "UZ37" in Austria and "Blauer Engel" in Germany, which are amongst the most stringent performance requirements in the European Union. Hence this design possesses a high potential as heating solution for low and passive energy houses. © Emerald Group Publishing Limited.

State-of-the-art packed bed models supply continuous concentration profiles as boundary conditions for subsequent CFD simulations of gas phase, leading to pre-mixed combustion conditions. However, in reality the “porous” nature of the packed bed leads to streak formation influencing gas mixing and combustion. Therefore, in the present work, in order to account for the influence of the streaks on gas phase combustion, a gas streak model based on a correlation between the local gas residence time and a mixing time has been developed based on numerical simulations. Finally, the streak model was linked with an in-housed developed hybrid gas phase combustion model suitable for laminar to highly turbulent flow conditions and applied for an under-feed pellet stoker furnace (20 kW_th) concerning the simulation of gas phase combustion and NO_x formation. The results in comparison with a simulation without the streak formation model show that the flue gas species prediction can be improved with the proposed streak formation model. Especially, in the region above the fuel bed (in the primary combustion chamber), this is of special importance for NO_x reduction by primary measures.

Control strategies of absorption heat pumping systems (AHPS, comprising heat pumps and chillers) often
perform insufficiently well, since they usually do not explicitly consider the systems’ dynamics and crosscoupling effects. One promising approach to improve their performance is to apply model-based control strategies since they would allow for an explicit consideration of these system characteristics. Therefore, mathematically simple models of the system to be controlled are required. This contribution proposes a new approach for such a model for a H2O-LiBr AHPS. The model results from the linearization of a more complex, nonlinear simulation model, leading to a simple, but physically still meaningful linear state-space model structure. The experimental validation shows that the developed model describes the system’s dynamics and cross-coupling effects sufficiently well and indicates that it is suitable to serve as a basis for the development of a model-based control strategy for AHPS.

Biomass has the potential to make a major contribution to a renewable future economy. If biomass is gasified, a wide variety of products (e.g., bulk chemicals, hydrogen, methane, alcohols, diesel) can be produced. In each of these processes, gas cleaning is crucial. Impurities in the gas can cause catalyst poisoning, pipe plugging, unstable or poisoned end products, or harm the environment. Aromatic compounds (e.g., benzene, naphthalene, pyrene), in particular, have a huge impact on stable operation of syngas processes. The removal of these compounds can be accomplished by wet, dry, or hot gas cleaning methods. Wet gas cleaning methods tend to produce huge amounts of wastewater, which needs to be treated separately. Hot gas cleaning methods provide a clean gas but are often cost intensive due to the high operating temperatures and catalysts used in the system. Another approach is dry or semi-dry gas cleaning methods, including absorption and adsorption on solid matter. In this work, special focus was laid on adsorption-based gas cleaning for syngas applications. Adsorption and desorption test runs were carried out under laboratory conditions using a model gas with aromatic impurities. Adsorption isotherms, as well as dynamics, were measured with a multi-compound model gas. Based on these results, a temperature swing adsorption process was designed and tested under laboratory conditions, showing the possibility of replacing conventional wet gas cleaning with a semi-dry gas cleaning approach.

The production of higher alcohols over a sulfidized molybdenum catalyst (MoS₂) using a biomass-derived synthesis gas has been studied at Güssing for several years. The mixed alcohol (MA) pilot plant uses synthesis gas provided by the biomass-based combined heat and power plant (CHP) Güssing. Parameter variations were carried out wherein temperature, space velocity and gas composition were varied to evaluate the impact on CO conversion, product distribution and yield. The influence of side reactions to hydrocarbons was also a research objective. A sufficient amount of experimental data was obtained during these experiments. Evidence for the influence of various reaction parameters was found, but the mass balance could not be closed. A mathematical model of the MA synthesis reactor was developed using the stationary equation-orientated flow sheet simulation software IPSE_pro. This publication gives an overview of modeling the MA reactor and condenser unit and testing the model with example calculations. Validated experimental results from 2012 parameter variation are shown and a comparison between experimental and validated quantities is carried out. A comparison with literature data shows that the observed tendencies are in good correlation to literature. The developed reactor model was enabling the possibility for carrying out a validation of the experimental data. IPSE_pro uses the method of least-squares to obtain the approximate solution of the overall determined system. The established model was very close to the actual MA pilot plant. The model is very accurate about MA liquid product compositions and all measured flows.

Several methods for identifying the phenomena of self-heating and off-gassing during production, transportation and storage of wood pellets have been developed in recent years. Research focused on the exploration of the underlying mechanisms, influencing factors or the quantification of self-heating or off-gassing tendencies. The present study aims at identifying a clear correlation between self-heating and off-gassing. Thus, different methods for determining self-heating and off-gassing potentials of wood pellets are compared. Therefore, eleven wood pellet batches from the European market were analyzed. For this investigation, three methods for the determination of self-heating, like isothermal calorimetry, oxi-press and thermogravimetric analysis, and four methods for off-gassing, like volatile organic compound (VOC) emissions measurements, gas phase analysis of stored pellets in a closed container by offline and by glass flask method and determination of fatty and resin acids content, were performed. Results were ranked according to the self-heating and off-gassing tendency providing a common overview of the analyzed pellets batches. Relations between different methods were investigated by Spearman’s correlation coefficient. Evaluation of the results revealed an equal suitability of offline and glass flask methods to predict off-gassing tendency and indicated a very significant correlation with isothermal calorimetry for the identification of self-heating tendency. The thermogravimetric analysis as well as the fatty and resin acids determination proved to be insufficient for the exclusive assessment of self-heating and off-gassing tendency, respectively.

In the last decades certification tests of small-scale biomass systems have impressively shown the improvement of the state of the art. Though, steady state measurements represent results only foroptimal operation. In practice results differ due to varying operating conditions. Therefore, of a test stand measurement method to derive realistic annual system efficiencies and emission factors is developed. The method includes a heat loss model for thermal storages too. It can be used to test automatically fed biomass boiler, manually loaded biomass boilers and boiler / heat accumulator combinations. For the evaluation of the measurement data a calculation method based on mass flows was developed. The results of our experiments show that the newly developed method is a good tool to evaluate small-scale biomass boilers. With this method an easy and reliable instrument to determine annual system efficiencies and emission factors for realistic boiler operation is provided. The application of the method will prove that modern small-scale biomass combustion systems have the potential to significantly contribute to the reduction of air pollutants and to increase overall energy system efficiency.

This publication focuses on the experimental investigation of a novel small-scale fuel flexible biomass combustion technology with a fixed-bed employing a low oxygen concentration. It was obtained through a low primary air ratio and the additional supply of recirculated flue gas. The plant was operated with spruce wood chips, which contained three different mass fractions of water, and miscanthus pellets. All relevant components of the released gas above the fixed-bed were measured, as well as the 3D bed temperature distribution. The balances confirmed a high experimental data consistency. Therefore, it was possible to determine the location of the four different conversion zones inside the fixed-bed: drying, pyrolysis, char gasification and char oxidation. The reduction of CO2 to CO in the char reduction zone worked efficiently across the entire grate area. Furthermore, the results showed that the water mass fraction of the fuel did not influence the dry product gas composition, but significantly affected the location for the release of pyrolysis products such as tars. It was found that the low oxygen concentration in the fixed-bed combined with flue gas recirculation was an effective method to reduce bed temperatures and therefore its inorganic emissions while significantly increasing feedstock flexibility. The investigations provided fundamental findings on the conversion and release behavior of the new technology under real operating conditions and are very useful for further experimental work and CFD simulations targeting the reduction of PM and NOX emissions.

Driven by increasing energy and raw material prices as well as changes in the legal framework the state of the art in the European Union has changed from waste management to resource management over the past 15 years. This has led to a higher appreciation of the resource “waste” as a secondary raw material as well as an energy resource. In this context the importance of effective waste processing in order to allow quality specific routing of waste streams has become very important. On the one hand material recycling requires a high purity of the waste material to be recycled. The prices to be achieved for the recycling material are highly dependend on the purity of the recyclables. The economic viability of treatment concepts very much depends on the rate of recovery of the recycling product. On the other hand the portion of waste that is thermally treated has increased and still is on the rise. Furthermore extensive efforts on the usage of waste fractions as Solid Recovered Fuels (SRF) in alternative thermal treatment processes with higher energy recovery are being undertaken. Alternative thermal treatment
processes have special demands on the quality of the waste streams to be treated due to process and product quality reasons as well as ecological concerns. Sophisticated waste pre-treatment concepts ensure compliance with required quality standards of wastes to be recycled or utilized energetically. In spite of that waste pre-treatment - in sometimes complex processes - the problem of disposal of the remaining residual waste fraction has to be solved, as the disposal of the residuals in compliance with the regulatory framework causes high expenses for the waste treatment plant operator. The first part of this manuscript focusses on the legal framework prompting the implementation of new waste processing technologies allowing an effective routing of waste fractions by material specific splitting of the over all waste stream. Most relevant in that respect are the EU Waste Framework Directive as well as the EU Landfill Directive and the EU Packaging Directive. Climate
policy and respective regulations are also influencing waste management practice. Additionally economic aspects for destination-process specific routing of waste streams are being addressed. In the second part of this manuscript the set-up of test runs as well as the results obtained and experiences gained based on the test runs are being reported. One test set-up aims at removing highcaloric waste components from waste streams of Mechanical-Biological Treatment (MBT) facilities in order to maximize the quantity of waste that can be landfilled. A second test set up deals with the processing of commercial plastic waste containing different types of polymers in order to gain pure recyclables. As the economic value of waste plastic depends on the purity in terms of individual polymers it is very important to separate individual polymers from mixed plastic waste. Near-Infrared
(NIR) sensor based sorting allows a separation of different types of plastics. The results of test runs are explained in terms of quality and yield of product gained as well as economical aspects. Although the prices for recyclables have fallen during the last months as a result of the financial and economical crisis leading to a decrease in the demand of recyclables it is assumed that gaining high quality waste fractions from mixed wastes for material recyling as well as energy recovery will become more important in the long run.

A promising way to substitute fossil fuels for production of electricity, heat, fuels for transportation and synthetic chemicals is biomass steam gasification in a dual fluidized bed (DFB). Using lower-cost feedstock, such as logging residues, instead of stemwood, improves the economic operation. In Senden, near Ulm in Germany, the first plant using logging residues is successfully operated by Stadtwerke Ulm. The major difficulties are slagging and deposit build-up. This paper characterizes inorganic components of ash forming matter and draws conclusions regarding mechanisms of deposit build-up. Olivine is used as bed material. Impurities, e.g., quartz, brought into the fluidized bed with the feedstock play a critical role. Interaction with biomass ash leads to formation of potassium silicates, decreasing the melting temperature. Recirculation of coarse ash back into combustion leads to enrichment of critical fragments. Improving the management of inorganic streams and controlling temperature levels is essential for operation with logging residues.